VoIP Phones Shop  

SIP-T46U Add 1-500x500

   

30 days money back

   

FreePBX / Asterisk Systems

     FreePBX (based on popular Asterisk engine) is one of the most popular VoIP PBX systems. Please see a configuration guideline to allow FreePBX working with our system.

1. You need to have installed FreePBX or naked Asterisk system. Please check FreePBX web site with a full configuration manual.

2. Login into Australian Phone "VoIP MY ACCOUNT", go to devices as shown below:

mor devices

7. Make sure that your device is configured as "Trunk", otherwise you may have problems with incoming calls and CID translation for outgoing calls. If you need to change the type of your device please advise us on This email address is being protected from spambots. You need JavaScript enabled to view it.

trunk

8. Please check your device credentials as shown below:

mor dev settings

 

Configuration for PJSIP Trunk for the latest FreePBX releases (legacy SIP trunk in the end): 

 

 9. Navigate to Connectivity, Trunks, and define a PJSIP trunk with next peer details:

 fpbx addpjsip

 10. Click to add SIP Trunk, enter "Australian Phone Company" trunk name and go to PJSIP Settings:

fpbx ausph pjsiptrunk

11. in PJSIP settings set: General settings for next trunk details:

fpbx pjsip general

Where :

  • Username: Your Username from billing portal, device settings above
  • Password: Your Password from billing portal, device settings above
  • SIP Server: sip.australianphone.com.au
12. Navigate to "Advanced" TAB of PJSIP settings and update next fields:

fpbx pjsip advanced
fpbx pjsip advanced pai

Set:
  • From Domain: sip.australianphone.com.au
  • From User: Your Username from billing portal, device settings above
  • Match (Permit): 103.12.10.97/32,118.127.57.173/32, 180.92.196.13/32, 223.252.19.169/32, 13.54.10.3/32 to set a list of our IP where FreePBX may accept traffic
  • Send RPID/PAI: Send P-Asserted-Identity header

13. Click on "Submit" at the bottom of the page and "Apply Config" on the top.

fpbx incoming apply

14,15. Navigate to Reports > Asterisk Info > Registries and make sure, that trunk is registered once configuration applied

fpbx pjsip registered

16. Now you need to define Outbound rules to be able to place calls via the trunk. Navigate to Connectivity > Outbound Routes:

fpbx outbound

17. Set a Route name as "Australian Phone" going to previously define "Australian Phone" trunk:

fpbx outbound trunk

18. Now you need to set Dial Pattern, how to route calls to this trunk:

  • "match pattern" = 0. - like all numbers starting from ZERO (National, Mobile, Service, Emergency 000 and International numbers) forward to trunk
  • "match pattern" = 1300. - like all 1300 numbers starting from 1300 forward to trunk
  • "match pattern" = 13XXXX - like all 13 numbers starting from 13 and 6 digits length forward to trunk
  • "match pattern" = 1800. - like all 1300 numbers starting from 1800 forward to trunk
  • "match pattern" = "XXXXXXXX" - like all numbers that have 8 digits (Local numbers) forward to trunk

fpbx pattern2

19. Click Submit to save changes.

20. Now you need to define inbound rules to receive calls from this trunk, navigate to Connectivity > Inbound Routes:

fpbx inbound

21. The best practice is when you have an individual route per phone number (DID). Set a description for your DID, like "Main Line" or "User Andres", type DID in E164 format like 61399998289 (11 digits without leading + or 0) and set destination where you would like to receive calls from this number, like extension or menu:

fpbx did

22. Click "Submit" on the bottom of the page and "Apply" on the top right.

fpbx apply

24. The system is ready. Call to free 09002 test number and try to call in on your number.


Configuration for legacy SIP Trunk (Please use only if PJSIP was not defined above or your system doesn't support PJSIP)


9. Navigate to Connectivity, Trunks, and define a SIP trunk with next peer details:

 

fpbx add trunk

 

10. Click to add SIP Trunk, enter "Australian Phone Company" trunk name and go to SIP Settings:

 

fpbx ausph trunk

 

11. in SIP settings set: Outgoing Trunk details:

 

fpbx outg trunk

 

type=peer
insecure=invite
qualify=no
sendrpid=yes
trustrpid=yes
dtmfmode=rfc2833
host=sip.australianphone.com.au
fromdomain=sip.australianphone.com.au
username=10023
fromuser=10023
secret=YourDevicePassword
disallow=all
allow=alaw,g729,gsm

 

12. Navigate to Inbound to define registration

 

13. Define a registration string: 10023:YourDevicePassword@sip.australianphone.com.au

 14. Click on "Submits" at the bottom of the page and "Apply" on the top.

fpbx incoming apply

 

15. Now your trunk should be online and registered, you may navigate to Reports > Asterisk Info > Chan_SIP_info and see registration status:

 

fpbx trunk registered


   

facebook share  Share your experience about us in your Socials !

   
© AUSTRALIAN PHONE COMPANY 2011-2022
...